referencia : BD115076
referencia : ADDIAVIPEC100
A traditional touring ski equipped with a rocker in tip and in tail, this REVERT is lightweight and very efficient uphill and fun, accurate and stable at the descent. Really causal, playful and fun, it will appeal to very good skiers, uphill or downhill.
- Rocker Tip and Tail
- Formula One 3D Light Sandwich: The F1 technology , which requires three main grooves, is used for the skis with a waist of more than 90 mm. To improve the performance on hard snow, some models use a stabilizer bar at the level of the front tip in order to lock in the curves at high speed.
- construction Pre-preg Composite: Our new facilities allows us to include in our skis the cutting edge technology pre-preg. Coming from the sector of the aerospace industry, this technology allows controlling the precise amount of epoxy resin used in each ski and maximize the usefulness of the fibre in terms of resistance and rigidity. This enables us to reduce the weight while maintaining the robustness, accuracy and regularity of each ski product. This clean process, as well as the presses pre-heated by solar energy, is the reference of what should be applied to top-of-range skis today.
- Paulownia wood core in 3D: a light wood, fast growing and easily renewable. It has the resistance of the poplar and the weight of the balsa
- ABS 5mm edging
- Power Edge: our edges are the thickest for durability in freeride
- SkinLock Clip in stainless steel
|Espátula (mm)||Patin (mm)||Talón (mm)||Radio (m)||Peso (g)||Unit weight|
Completely revolutionary, the DIAMIR VIPEC 12 is the first ski touring binding with inserts with defined triggering.
To be clearer, this "Low Tech" binding system allows a lateral security triggering combined with the automatic heel piece. A great novelty in the ski touring world!
Lightweight, it ensures maximum security. For understanding its system, its inserts are mounted on a lateral "rail". Thus, in a fall with torsion, this "rail" moves to facilitate wedging. And in case of fall at low speed, the insert switches on the outside so that nothing can interfere with the ejection of the shoe.
Featuring the Easy Switch concept which allows you to pass from downhill mode to walking mode easily with the help of your pole, it is easy to use.
To finish, it is endowed with a broad support point and high stability of the system, for a more direct transfer of forces more and therefore more effective.
- Lateral security triggering : Its automatic stop allows a side trip in 2 phases. In a first phase, the sliding block moves laterally with the pin toe piece unit. In a second phase, the pin toe piece unit tilts laterally, thus freeing up the shoe. After tripping, the toe piece can be turned back to its initial position with a simple gesture. Note that the shoe shall be released only if the dynamic stroke of 11mm and the restoring force set have been crossed.
- Security frontal triggering: Its automatic toe grounder allows frontal triggering assured by the lateral tilt of the heel pin unit housed in the heel chassis. They move on a dynamic race of 4 mm and, after exceeding the restoring force set acting on the retention wedges of the rear inserts of the shoe, the latter is released.
- Defined security triggering: The active longitudinal compensation is the key of the defined triggering. The contact pressure of the shoe must remain constant for the triggering mechanisms to provide a defined triggering in all situations. Thanks to the Pin Safety system, the active longitudinal compensation provides constant pressure through the coming and going of the heel piece on the guide plate even during an extreme ski bending.
- Système Easy Switch : This Easy Switch system allows quick and simple donning and doffing. This system also facilitates the passage of the binding from the downhill mode to walking mode. The VIPEC 12 binding is compatible with all ski touring boots equipped with inserts.
- 3 levels of tilt: The Comfort Lift system allows 3 levels of tilt, 0°, 9° and 13°. The tilt change is done quickly and easily with your pole.
- Stop ski 100 mm
- DIN value: 5-12
- Unitary weight (without stop skis): 520 g (verified weight 485 g)
- Stop skis weight (unitary): 65 g (verified weight 65 g)
|TALLA||Peso (g)||Unit weight|