From a range consisting of 3 graphics celebrating different periods of the career of the skier Doug COOMBS the COOMBACK reflect very well the versatility of the skier.
Its 102mm at waist, its all-terrain rocker and its lightness allow it to offer good buoyancy and great convenience to be able to ski on any slope you want to access.
- Construction : Fibre Triaxiale, Cap, Sapin/Poplar / Maple
- All terrain Rocker : This Rocker has been developed to be used in all snow conditions. The raised tip improves performance on variable and soft snow and facilitates the release curve, while the camber underfoot provides power, energy and edge grip on hard snow needed.
- Powder Tip All new skis of the freeride range have a tapered tip and the lowest profile in order to optimize the foreseeable nature of the tip in soft snow. The tips designed in such a way have their widest point declined to reduce the weight of the tip and the resistance in soft and changeable snow
- Progressive sidecut: Larger ski front, thinner tail and a progressive radius is a combination of two different radii whose purpose is to increase the versatility of the wider skis under the foot. In general, the skis have rather a single radius. This works very well on skis rather thin, but can make driving wider skis underfoot more difficult, especially in transformed snow. The use of progressive radius on wider skis improves the triggering of the turns and the performance on hard snow.
- Snowphobic Topsheet : Topsheets snow unloaders, specific of the Back models. Accumulated snow on a skiing can increase during a climb. Our SnowPhobic top system prevents the snow from accumulating on your skis and weighing you down. In fact, we have developed the tops specifically if the Back models using the same hydrophobic material on the soles but with lower thickness. You can even add wax on the topsheet to increase this effect of load shedding.
- Skin Grommets : All the Adventure skis are provided with a hole at both ends. The holes are covered, and can be opened simply with a flat-head screw, for use in ski touring. They are primarily designed for the installation of skins, but can also be used in the manufacture of a rescue sledge in backcountry, and also for marking support points in the snow.
- Carbon web: The structure MOD is wrapped with a carbon fibre, carbon strands are arranged at specific angles for added torsional rigidity of the secondary core. This allows retaining a light ski while providing the torsional stiffness to the places where it is needed.
|Espátula (mm)||Patin (mm)||Talón (mm)||Radio (m)||Peso (g)|
Completely revolutionary, the DIAMIR VIPEC 12 is the first ski touring binding with inserts with defined triggering.
To be clearer, this "Low Tech" binding system allows a lateral security triggering combined with the automatic heel piece. A great novelty in the ski touring world!
Lightweight, it ensures maximum security. For understanding its system, its inserts are mounted on a lateral "rail". Thus, in a fall with torsion, this "rail" moves to facilitate wedging. And in case of fall at low speed, the insert switches on the outside so that nothing can interfere with the ejection of the shoe.
Featuring the Easy Switch concept which allows you to pass from downhill mode to walking mode easily with the help of your pole, it is easy to use.
To finish, it is endowed with a broad support point and high stability of the system, for a more direct transfer of forces more and therefore more effective.
- Lateral security triggering : Its automatic stop allows a side trip in 2 phases. In a first phase, the sliding block moves laterally with the pin toe piece unit. In a second phase, the pin toe piece unit tilts laterally, thus freeing up the shoe. After tripping, the toe piece can be turned back to its initial position with a simple gesture. Note that the shoe shall be released only if the dynamic stroke of 11mm and the restoring force set have been crossed.
- Security frontal triggering: Its automatic toe grounder allows frontal triggering assured by the lateral tilt of the heel pin unit housed in the heel chassis. They move on a dynamic race of 4 mm and, after exceeding the restoring force set acting on the retention wedges of the rear inserts of the shoe, the latter is released.
- Defined security triggering: The active longitudinal compensation is the key of the defined triggering. The contact pressure of the shoe must remain constant for the triggering mechanisms to provide a defined triggering in all situations. Thanks to the Pin Safety system, the active longitudinal compensation provides constant pressure through the coming and going of the heel piece on the guide plate even during an extreme ski bending.
- Système Easy Switch : This Easy Switch system allows quick and simple donning and doffing. This system also facilitates the passage of the binding from the downhill mode to walking mode. The VIPEC 12 binding is compatible with all ski touring boots equipped with inserts.
- 3 levels of tilt: The Comfort Lift system allows 3 levels of tilt, 0°, 9° and 13°. The tilt change is done quickly and easily with your pole.
- Stop ski 100 mm
- DIN value: 5-12
- Unitary weight (without stop skis): 520 g (verified weight 485 g)
- Stop skis weight (unitary): 65 g (verified weight 65 g)
|TALLA||Peso (g)||Unit weight|
K2 fue fundada en 1961 por los hermanos Bill y Don Kirschner en Vashon Island, cerca de Seattle, en los Estados Unidos.
K2 es conocido por su tecnologia de esqui de vanguardia en fibras de vidrio lo que hizo esquis mucho mas ligeros y mas reactivos que sus contemporaneos en metal y madera. Fabricante N ? 1 en los Estados Unidos, la marca atipica americana es conocida por sus productos innovadores que ofrecen gamas de esquis anchos y new school con espatulas mas o menos rocker.
El grupo K2Sport incluye a K2Skis, K2Snowboard, Line, Full-Tilt, Ride, Morrow o Madshus. K2Sport forma parte del grande grupo Jarden que incluye marcas como Volkl, Marker, sino tambien en areas muy diferentes con camping Gaz, Spontex o Mapa.